Skip to content
Snowblowers

Snow Blower Won’t Start After Summer? Fix It Before the First Storm

By Jeff Mercer · Updated November 16, 2026 · 8 min read
A gray house with an empty driveway and fallen leaves in late fall, before the first snow

Photo by Mandie Barber on Unsplash

DisclosureSome links on this site are affiliate links — if you buy through one we may earn a small commission at no extra cost to you. It never decides an answer. A post a brand paid for, or one with a brand's paid link to its product, says so in its first line.
A gray house with an empty driveway and fallen leaves in late fall, before the first snow
Photo by Mandie Barber on Unsplash

A snow blower that ran fine last March and won’t start in November almost always has the same problem: the gas sat in it all summer. That’s the good news, weirdly. It’s usually a cheap fix, and you can do most of it yourself in an afternoon (before the first real storm makes it urgent).

Start with the cheapest checks and work up from there. Don’t skip ahead to the carburetor.

A lot of “dead” snow blowers just need a key or a fresh tank of gas.

The Free Checks Nobody Wants to Admit They Missed

Before you pull anything apart, go down this list. It takes 2 minutes, and these are the first things to rule out on any two-stage machine.

What is in itFive free checks before any toolsEach one takes seconds.
  • The keyFreeAll the way in
  • The fuel valveFreeOpen, under the tank
  • The chokeFreeOn for a cold engine
  • Gas in the tankFreeRock it, listen for the slosh
  • The plug wireFreeBoot pushed on until it clicks

Start with the key. Most snow blowers have a removable one, and the engine won’t start without it (it’s often in a kitchen drawer, on the same hook as last year’s ice scraper).

Then the fuel valve. A lot of machines have a little shutoff under the tank, and if you closed it for storage, it’s still closed. Is the choke on? A cold engine needs it. And is there actually gas in the tank? Give the machine a rock and listen for the slosh.

One more that catches people out is the spark plug wire. If it got knocked off over the summer, or you pulled it for safety and forgot, you’ll get nothing. Push the boot down onto the plug until it clicks.

Stale Gas Is the Usual Suspect

A gas pump with its grade buttons and nozzle hanging at a station island
Photo by Dawn McDonald on Unsplash

Gas doesn’t keep. Untreated fuel starts to break down after about 1 month, and a snow blower usually sits 7 or 8 months between storms. By fall, what’s in the tank is stale gas that doesn’t light well, and some of it has turned into a sticky varnish in the fuel system.

So drain it.

Run the tank down or siphon it into an approved can, then refill with fresh gas. Check the owner’s manual for the fuel yours wants. A typical two-stage machine runs on regular unleaded of at least 87 octane with no more than 10% ethanol, and E85 is off the table. For most small engines, E10 is the limit and E15 isn’t approved, so skip that pump at the gas station.

Add a fuel stabilizer to the new gas, too. It keeps the fresh fuel fresh and helps stop the carburetor from gumming up again. Then try starting it. If the old gas was the whole problem, it’ll usually catch within a few pulls. The same shelf-life rules apply to how long gas can sit in a mower.

The Cold-Start Routine, in Order

Plenty of snow blowers that “won’t start” are just being started wrong. It’s been 8 months or more since you last did it, so honestly, who remembers the order? Here’s the usual routine for a two-stage machine with a key, a primer and a choke. Yours may be a little different, so check it against your own manual.

What to expectStarting a cold snow blower, in orderThe usual order on a two-stage machine. Check your own manual.
  1. Step 1Choke onCold engine only
  2. Step 2Key in, fuel valve onBoth are easy to forget after storage
  3. Step 3Throttle to fastThe rabbit, not the turtle
  4. Step 4Prime 3 timesThumb over the vent, 1 second each press
  5. Step 5Pull or push the buttonElectric start: 5 seconds max, then wait 1 minute
  6. Step 6Ease the choke offGradually, as the engine warms

The primer is where people go wrong. Three presses on a cold engine, with your thumb covering the little vent hole, holding each press for 1 second. Not 10 presses. Not 10 seconds either.

Pumping it over and over floods the engine. And never prime a warm engine at all.

If you think you’ve flooded it, the fix is backwards from what you’d guess. Move the choke to off and try again (more air clears the extra fuel). Once it does start, ease the choke off gradually as it warms up, rather than slamming it off right away.

Pull the Spark Plug and Read It

Spark plug wires with red boots seated on top of an engine next to its exhaust pipes
Photo by Markus Spiske on Unsplash

Fresh gas in and it still won’t catch. Time to pull the spark plug. It’s the cheapest diagnostic tool on the machine, and it tells you which half of the engine to blame.

Which oneWhat the spark plug is telling youPull it after a few tries and look at the tip.
If Wet with fuelFuel is getting in: check the sparkPlug, wire or ignition
If Bone dryNo fuel arriving: check the fuel sideValve, gas, carburetor
If Cracked porcelainReplace the plugA few dollars, five minutes
If Black or oilyClean or replace, set the gapGap number is in the engine manual

A wet plug means fuel is getting through, so the problem is on the spark side. A dry plug after a bunch of pulls means fuel isn’t reaching the cylinder, so look at the fuel system (the valve, then the tank, then the carburetor).

While it’s out, look at the tip and the white porcelain. A cracked plug goes in the trash. A black, sooty or oily one should be cleaned or swapped, and the gap checked against the number in your engine manual. A new plug costs a few dollars and takes 5 minutes, so if yours has more than a season on it, I’d just replace it. You can confirm spark with an inexpensive spark tester if you want to be sure.

Whatever you do, push the spark plug wire back on firmly when you’re done, or you’ll be right back at the start of this list. We cover the signs of a worn plug in this spark plug guide.

When the Carburetor Is Gummed Up

Two hands work a small carburetor off a single-cylinder engine
Photo by Mick Haupt on Unsplash

Dry plug, fresh gas, open valve, and it still won’t fire? Then the carburetor is the likely culprit. Old gas left without a stabilizer goes gummy, and that gunk clogs the tiny passages fuel has to squeeze through. Those same deposits can also damage the fuel hoses, the filter and the tank.

Look at what came out of the tank, too. If the old gas was cloudy, or you see beads of water at the bottom of the can, that’s contaminated fuel. Water is heavier than gas, so it settles at the bottom of the tank, right where the fuel line picks up. The fix is a full drain and clean fuel, not a top-up.

Past that, the carburetor has to come off and get cleaned, or be replaced. If you’re comfortable with small engines, it’s a reasonable job. If you’re not, this is the point where I’d stop and call the small-engine shop. But call soon. A carburetor rebuild done wrong can leave you worse off than when you started, and in November every shop has a line.

Electric Start: Use It, Don’t Cook It

The push-button electric starter on a red gas snow blower, an orange outdoor extension cord plugged into its socket
Image made with AI: no real photo matched this section.

If your machine has a push-button electric start, it’s a big help on a cold morning. It plugs into a regular household outlet, not a battery. Use a grounded 120V outlet and a three-prong cord that’s rated for outdoor use and for at least 13 amps.

Here’s the part people ignore. Hold the button until the engine catches, but never more than 5 seconds at a time. Then wait at least 1 minute before you try again. Leaning on that button for 30 seconds straight is a great way to overheat the starter motor. Now you’ve got two problems instead of one.

With the pull cord, draw it out slowly until you feel resistance. Then give it one firm, fast, full-arm pull. If the handle won’t pull at all, ice may have locked it up. Move the machine somewhere warm to thaw before you yank harder.

It Starts, Then Dies? Check These

An engine that fires and then quits is giving you a better clue than one that won’t start at all. The usual causes are short, and most are cheap:

What is in itStarts, then dies: the usual causesCheapest check first.
  • Choke left onFreeMove it to off once it warms
  • Fuel valve half shutFreeOpen it all the way
  • Clogged cap ventA new capEngine starves after a minute
  • Bad or old gasA tank of fresh gasDrain it, refill, add stabilizer
  • Fouled plugA new plugClean or replace, check the gap
  • Ice in the augerFreeEngine off, key out, clean-out tool

A clogged fuel cap surprises people. The cap has a tiny vent so air can replace the gas as it’s used. If that vent clogs, the engine starves after a minute and dies, then starts again once you’ve opened the cap. A new cap is the fix (one of the cheapest parts on the whole machine).

The choke is the other common one. Leave it on after the engine warms up and the mix gets too rich, so the engine runs rough, smokes a bit and may stall. Move it to off. And if the engine bogs and dies the moment you engage the auger, shut it down, pull the key and wait for everything to stop moving before you look in the housing. A chunk of ice or a rolled-up newspaper in the auger will stop a healthy engine cold. Never reach in there with your hand. Use the clean-out tool that clips to the housing.

When to Hand It to the Dealer

A smiling mechanic in a work shirt and gloves stands at an open engine bay in a repair shop
Photo by Quilia on Unsplash

Here’s a simple bar. A snow blower in good shape should start within three pulls. If you’ve done everything above (fresh gas, the right routine, a good plug) and it still won’t, take it in. A starter that clicks but doesn’t turn is a job for the dealer. So is a dead electric start circuit, or an engine that coughs and smokes.

Go early. The first forecast with real snow in it is when everybody else finds out their machine won’t start either.

And next spring, give future you a break. Storage takes about 10 minutes. Add stabilizer to the gas and run the engine for at least 5 minutes so the treated fuel reaches the carburetor. Then close the fuel valve and let the engine run until it stops on its own. That leaves the carburetor dry instead of full of gas that’ll be stale by fall. If you haven’t bought a machine yet and are still choosing, our single-stage vs two-stage snow blower guide is a good place to start.

Before you start the repairWe are not certified small-engine technicians. Before any repair, pull the spark plug wire and let the engine cool. Anything involving blades under a raised machine, fuel system leaks or transmission internals — if you're not sure, have a dealer or small-engine shop look at it.

Written by

Jeff Mercer

Jeff Mercer writes GardenTooly's answers to the questions people type into a search bar while standing next to a machine that won't behave: why the deck shakes, why the mower dies when it warms up, whether a bent blade shaft can be straightened, what the difference between two transmissions really means for you, and which fuel additive is worth the shelf space.

Each answer starts with the cause that is most likely and cheapest to check. Where it comes from the owner's manual, a service bulletin or what owners report, it says so, and anything involving blades, fuel, a jacked-up machine or a hydrostatic transmission gets a plain "take it to a shop" when that's the right call.

A note on our names: GardenTooly is written by a small team under pen names, one name for each job, and Jeff Mercer is the name on our mower and small-engine guides. We are not certified small-engine technicians, and we don't sell equipment.